How to Fix Error Code B200 for Canon Pixma MG6320 Printer? [Solution]

In: Canon, Error B200   0 Comment  

Error Code B200 Canon Pixma MG6320

Each person of Canon inkjet printer, may have the chance to seek out the B200 Error Code on the printer. The reason for error within the Canon Inkjet printer could be very variatifly, however the primary of it's Error Code B200. The B200 error perhaps can level to a number of various things, however mainly it’s an issue with the print head overheating. Different that, the issues basically have relation with waste ink tank full, Waste ink pad full and different a part of the printhead.

For the Error Code B200 on Canon Pixma MG6320, Canon technicians recommends to customers some generic fixes for this drawback. This recomendation like flip OFF of the printer and switch ON it. However we discovered some extra resolution strong fixes that contain working with the printer heads.

Error B200 Causes :
Why the printer is error and What Units Off this Printer Error?

Amongst of the causes:

The error on the printer occurred when a papers has been printed and the ink utterly empty, in situation if a cartridge is totally empty.

In line with Canon, it even be attributable to overseas cartridges, with which the printer cannot cope. Cleansing and checking the printheads will assist of this error. However it's a must to bear in mind, it resolution provided that the printer is not assured, because the guarantee could also be void, as a result of you could harm the printhead.

One other of the causes:

The opposite reason behind this error normally happens when totally different formulation of ink have been utilized by the printer. This error some occasions happens whenever you change or refill an OEM cartridge with not legimate product and this product in typically with low-cost worth provides which have questionable toner high quality and/or construct high quality.

Troubleshooting Information :
Tips on how to Repair the printer with Error B200?

There are two section to unravel this error; {hardware} technical section and software program technical section of the printer.

Part 1: {Hardware} Technical Part

On this section, we now have 5 resolution for resolve the printer error code B200. This options come from quite a few occasions expertise of printer technician after face similar error by repeatedly.

Try the fixes and resolution of this drawback, we are going to guides step-by-step for clearing this drawback. Choose one of many 5 out there options under:

Answer 1:

1. Flip OFF the printer.
2. Unplug the printer from the facility supply.
3. Open the printer cowl then reveal the ink cartridges.
4. Take away the printhead from the printer be fastidiously.
5. Clear the Printhead together with the Ink Cartridges. 
6. Clear the contact pads within the printer with a contact cleaner or a very good pencil eraser.
7. Reinstall the printhead once more.
8. Reinstall the ink cartridges thereafter earlier than powering up the printer.
9. Run the “Auto Head Alignment” for testing the printer.

Answer 2:

1. Flip OFF Energy of the Printer.
2. Open the print head bay (as if you had been about to vary inks).
3. Flip ON energy.
4. Look ahead to print carriage to begin shifting to the left and let it go previous half approach.
5. Earlier than print carriage reaches left hand facet (however after going midway throughout) shut the quilt.
6. Turned on the Printer once more.

A lot of printer customers do that easy resolution and the issue of them printer is solved.

Answer 3:

1. Open printer.
2. Take away ink cartridges.
3. Un-install printhead.
4. Clear again of the printhead (digital pins) with alcohol (isopropylen cleansing alcohol if potential). Be certain the pins are 100% clear.
5. Flip off the printer (don't shut it!) by plugging-off energy wire (don't use energy button).
6. Clear digital pins in printer (the pleace the place you put in printhead). Be certain its 100% clear.
7. RE set up printhead, then set up ink cartridges.
8. Plug in energy wire.
9. Flip printer ON normaly.
10. Verify if printer is working normaly (no errors).

Answer 4:

1. Flip OFF the printer.
2. Disconnect the printer from the facility supply.
3. Open cowl of the printer and take away the colour cartridges.
4. Take away the sled during which the cartridges had been beforehand positioned.
5. clear the cartridges with water be fastidiously. For optimum outcomes, clear it use isopropanol (there within the pharmacy), in order that the printhead cannot clog with lime.
6. Ensure that the golden contacts usually are not moist, in any other case you possibly can harm the print head.
7. Dry the whole lot be fastidiously, ensure that no residual water will get into the printer.
8. Reinstall cartridges and carriages within the first place.
9. Flip ON the printer once more.

If the message of "Error B200" seems once more, the printer need to be switched off once more. And The flap need to be opened earlier than switching on. When switching ON once more with the flip open, the printer then performs a self-test: Then the error mustn't happen to repeat extra typically, that it really works and the issue solved.

Answer 5:

1. Unplug the facility cable.
2. Open the printer.
3. Push the entire print head mechanic to the middle.
4. Whereas the printer nonetheless open, plug the facility and switch it ON. 
5. When the printhead nonetheless shifting and goes to the very LEFT, shut the quilt. 
6. Wait till its boot up. 

When you have making an attempt and following step-by-step of  the primary section information and the error nonetheless pops up in your printer, proceed to the second section under. 

Part 2: Software program Technical Part

On this section, you have to to have an web connection and administrator entry on a pc. For this section, comply with the step-by-step under:

1. Replace the printer drivers in addition to the Canon IJ Printer Utility software program.
2. Click on “Begin” out of your Home windows desktop and click on “Gadgets and Printers.”
3. Proper-click the Canon MPxxx (in accordance your Canon code Model) and click on “Properties.”
4. Choose the “Upkeep” tab and click on “Deep Cleansing”.
5. Run a Nozzle Verify from the Upkeep tab when the deep cleansing is completed.